CODAPAK

Sunflower oil filling equipment: how to avoid splashing

Sunflower oil flows easily, so when the container stops, the stream is agitated and produces splashing and foam. We explain how dosing equipment with a piston dispenser and container feed without stopping delivers a stable dose without splashing and overflow, and what to clarify before selection.

Vegetable oil filling equipment: general view of the line in the workshop with an upper hopper and protective doors

For sunflower oil, two things matter: the container does not stop under the nozzle, and the dose is set by the volume of the piston cylinder. This scheme provides an even surface in the bottle, a stable dose and less splashing and overflow.

Questions covered

01
Why does splashing and foaming occur when filling oil, and how can they be reduced?
02
How can a stable dose be achieved in every bottle when the oil is highly fluid?
03
What needs to be clarified and checked before selecting equipment for sunflower oil filling?

Why sunflower oil is a separate filling challenge

Sunflower oil is a free-flowing food liquid of low viscosity: it moves quickly through the pipeline, is sensitive to jerking of the containers, and when the stream falls into the bottle it is easily agitated, foams and splashes.

On such a line, glass and PET containers of different heights, diameters and neck finishes usually coexist, and filling into glass or PET containers followed by capping runs in a single flow with transport between stations.

The buyer and the process engineer look at three things: the dose must not fluctuate from bottle to bottle, the line must not stop at every position, and the machine itself remains a link in the filling and packaging line before capping and labeling.

Food production hygiene is added: the working surface and pipelines must be properly washed between shifts and products.

What holds back older oil filling schemes

Manual and gravity filling with a ladle or by level in the container leaves the dose dependent on the operator and on the remaining product: hence overfilling, underfilling and weight variation within one batch.

Positional filling, where the bottle stops under the nozzle and then starts abruptly, is especially inconvenient for oil: during start-up and braking the product is agitated, the surface fluctuates, splashing and foam appear, and some of the product goes to wiping the containers.

A specialized machine bought for one fixed bottle type requires the bottle holder and deflectors to be set up again when the neck finish, height or diameter changes, that is, line downtime.

A pneumatic dispenser adds its own instability: the piston stroke depends on air pressure, when the pressure drops the dose drifts, and systematic overfilling appears.

How filling works on a piston doser with container follow

The dose is set not by valve opening time but by volume: the piston dispenser first draws the product into a cylinder that itself serves as the measuring chamber, then pushes it into the nozzle, while a three-way rotary valve switches the directions "hopper — dosing cylinder" and "dosing cylinder — filling nozzle".

Splash is eliminated by container follow: four groups of filling heads move horizontally together with the bottle on a slat conveyor — via a helical rack, a gear on a servo motor and linear guides, while each dosing cylinder runs on its own servo drive.

Overflow is closed off by level: a level sensor in the U-shaped hopper controls the feed pump and stops the supply when the controlled value is reached, so product does not run over the edge and the line does not wait for an operator.

For container changeover there are interchangeable filling nozzles, a bottle holder with adjustable gripper pitch, adjustable guide rails and head height lift — these are the adjustment points when switching from one bottle type to another.

Dosing cylinder of oil filling equipment with a stainless steel sight glass

Dose drive, electrics and flushing: what to look at in the design

The dose is held by a servo drive, not by air: the number of revolutions and the motor speed set the piston stroke, and the materials explicitly note that unstable air pressure affects the stroke and shifts the dose — the servo drive removes this dependency.

Control is distributed transparently: ten servo drives — four for the piston pumps, four for horizontal movement of the heads, one for the bracket height and one for the slat conveyor; the overall logic runs on a PLC, and the pneumatics of the valves, head lift and holder are fed from an air preparation unit.

Workshop hygiene is covered by steel and access: a stainless steel frame, transparent safety doors of tempered glass, quick-release pipe clamps, a flush valve and a drain to a separate tank for contaminants — cleaning runs with clean or sterile water through the circuit.

For the setup technician, an HMI with dose setpoint, speed and filled-bottle counter is important, along with a transparent electrical cabinet door, cooling fans and a protective cable duct for pneumatic tubes — the condition is visible without disassembling the machine.

Control cabinet of the filling equipment: PLC, relays and terminal blocks inside the cabinet

What to clarify when selecting and what result to expect

Dose range, capacity, dosing accuracy, viscosity window, power supply and power, air pressure, dimensions and weight in open materials are not confirmed as values for this task — they are clarified on request at the selection stage for a specific container and product.

Compatibility specifically with sunflower oil and its viscosity is verified by sample: oil is treated here as one of the fluid products for which the scheme fits logically, not as a confirmed design case.

Expected result for the scheme: continuous container feed, an even surface in the bottle without splashing, a stable dose from bottle to bottle, less spatter and overflow thanks to container following and a stable dose, and accordingly fewer rejects and rework.

The machine is installed in the line as a filling unit, while capping and labeling remain adjacent operations that must be coordinated for container feed and conveyor height.

Food liquid filling line with conveyor, dosing heads and control panel

Application boundary

Filling parameters — dose range, capacity, accuracy, viscosity window, power supply and power, air pressure, dimensions and weight — are not confirmed and are clarified on request at the selection stage. The materials do not contain confirmed parameters for sunflower oil: compatibility with a specific product and viscosity is checked against a sample at the selection stage. The operating conditions of the line — container type, neck finish and bottle height, cleaning requirements and integration with capping — are agreed based on a product and container sample.

Verify the dose on your own oil

Send us the container type, dose volume and line requirements — we will select a configuration and agree on a test with a product sample.